200KA SUS 304 Lightning Protection Rod , Early Streamer Emission System

ESE Lightning Rod EarlyHD-T5.3 Advance Discharge Lightning Rod Lightning Protection SystemESE Lightning Rod Early HD-T6.3 Advance

Discharge Lightning Rod Lightning Protection SystemHD-T6.3/0.5 advance discharge lightning rod made of special stainless steel material, needle (needle) height 500mm, receiving flash capacity 200KA, with simple installation, corrosion resistance, suitable for direct lightning protection of small objects. Can also be installed with lightning rod installation bracket will be installed in a relatively high position, as a standard receiver use.

Lightning rod protection radius as shown in the figure.

Lightning rod body using threaded connection, needle rod and flange plate using on-site welding, installation and fixing according to the site will be flange plate fixed root can be, while the lead wire and flange plate connection, can be fixed in the flange plate can also be welded on the steel pipe, can also be fixed directly on the daughter wall above.

Grounding resistance requirements. 10 ohms.

"HDE" lightning rod in the traditional lightning rod based on the addition of an active trigger system, this trigger system can establish a repetitive high-voltage pulse signal, in the discharge process in due time to produce a continuous discharge path and thundercloud downstream pilot rendezvous, the lightning current into the earth.

"HDE" through a combination of pulse transformer and oscillator to achieve a strictly controlled frequency and amplitude of high-voltage signal emission technology; its energy from the electrostatic field and electromagnetic field and transformed into a high-voltage signal to the tip of the needle, generating a large number of ions, this function so that "HDE" issued by the upstream pilot to advance away from the lightning rod tens of meters or even hundreds of meters and the downstream pilot from the thundercloud to meet the flash, thus expanding the protection range of the lightning rod.

1．2 “HDE” The workflow of lightning rod

Thundercloud formation when the thundercloud prompted the formation of electromagnetic fields between the ground and the clouds, the magnetic field strength at ground level can exceed 14KV/M.

a) At this time, the lightning detector in advance of the discharge lightning rod will detect a certain electromagnetic signal

b) then the detected lightning signal by the sensor will signal transmission to the trigger device

c) trigger device will signal amplification to prompt the next level of high-voltage generator action

d) high voltage generator will generate high voltage to the high voltage pulse generator

e) High-voltage pulse generator will be high voltage oscillation after the generation of electric ions directly to the stainless steel electrode

f) stainless steel electrode tip of the electric ion through the venturi effectively to the tip of the lightning rod.

Type

Direct lightning rods / Special lightning rods / Pre-discharge lightning rods
Direct lightning rods
Direct lightning rods
Optimised lightning rods
Optimised lightning rods
Pre-discharge lightning rods
Early pre-discharge lightning rods
Direct lightning strike
Suitable for petrochemical warehouses, radio and television, petrol stations, architectural buildings, beacon stations, communication base stations, meteorological stations, military bases, radar rooms, bank buildings.
Special
Suitable for microwave communication stations, radar base stations, beacon stations, communication base stations, military bases, radar rooms, bank buildings, astronomical and meteorological stations and other important places in higher architectural buildings.
Pre-discharge
When the lightning rod is cut off by lightning, the lightning received by the lightning body, through the lightning waveform processing device, using the shell and the centre grounding rod between the 3mm gap, constituting a coupling capacitor, while the shell through the inductive coil grounding (centre grounding rod) When the downstream inducer is close, due to the high frequency. The inductor is in an open circuit state and the capacitor presents a short circuit characteristic for high frequencies, so that the electric field strength on the surface of the flash catcher increases rapidly under the action of the coupling capacitor until the avalanche process is triggered, thus releasing the lightning current to the ground in an instant and effectively achieving lightning safety.

 

 

 

Company Profile

Hunan Hertz-Ohm Engineering Group Co., Ltd.(referred to as: Hunan Heou ) is a comprehensive engineering consulting company established in Changsha in cooperation with Heilongjiang Hengdian Lightning Protection Engineering Co., Ltd. Group. The main purpose is to consolidate the original business content of Hengdian Lightning Protection Company to South China, and to increase and promote new engineering consulting and management business scope. The company's service areas involve electric power, mobile communication, wind power, solar energy, chemical petroleum, national defense and civil intelligent buildings, and industrial control fields.

Our Advantages

Title goes here.

Hunan Heou Company and Heilongjiang Hengdian Company realized the north-south cooperation, integrated the research resources of domestic first-class colleges and universities, created the main body of early development with related businesses in the field of lightning protection, took engineering management and consulting business as the new expansion goal, combined foreign trade and new technology A comprehensive engineering consulting company integrating research and development.

Product packaging